()

Step by Step Exadata : Snapshot Filesystem Backup


During the Exadata patching event, it is advisable to take the backup of the filesystem, and the easiest way to take filesystem backup is with a snapshot of the mount point feature. Taking snapshot backup is not an Exadata feature but it is Linux functionality and can be used for any server running with Linux (RHEL/OEL etc.)

By using below mentioned commands and procedure you may take OS backup (compute nodes), considering there is no customization done on Exadata with the default shipped filesystem. However, the same method can be used as well if you created any additional mount points on Exadata for any other purpose e.g. OEM, etc.


Starting with X8M with Oracle Exadata System Software release 19.3, Exadata database server using new filesystem i.e. XFS (earlier it was ext3/ext4).


Additionally, arrangement of system layout of filesystem is also changed e.g. additional mount points are created e.g. /home, /var, /tmp, /var/log & /var/log/audit along with /root & /u01. Therefore it is necessary to backup all filesystems (mount points) for OS backup before appliance patching.

Exadata X8M filesystem Layout

I am describing the process for xfs filesystem layout but the same steps can be used for older filesystem layout as well with few changes. I will try to highlight that as well.


Note: You need root access on compute nodes to perform this activity.


Step 1: Mount the share where you want to take backup. In my case, I am taking backup at location “/export/backup_lvm01” but this can be changed as per your environment.


Step 2: Identify active partition for image active on Exadata with imageinfo command

Here, highlighted in the red box is an active partition for the root mount point. There is mirrored of the same partition with the name LVDbSys2. At the time of taking backup, it is important to identify, active partition for root. Here are active partition is LVDbSys1, therefore I will use the same partition in commands but you can identify and change the command accordingly.


Step 3: Create a snap shot of root mount point.


XFS filesystem :

$/sbin/lvcreate -L3G -s -c 32K -n LVDbSys1-SNAP /dev/VGExaDb/LVDbSys1


EXT filesystem:

$/sbin/lvcreate -L3G -s -n LVDbSys1-SNAP /dev/VGExaDb/LVDbSys1


Step 4: Label the snapshot with different name than actual partition. This is mandatory otherwise during patching , system restart will fail during pre-reboot step of Exadata patching.


XFS filesystem :

$xfs_admin -L LVDbSys1_BKP /dev/VGExaDb/LVDbSys1-SNAP


EXT filesystem:

 $e2label /dev/VGExaDb/LVDbSys1-SNAP LVDbSys1_BKP


Step 5: Mount the snapshot partition


XFS filesystem:

$mdkir /mnt/backup_snap_root

$mount -o nouuid /dev/VGExaDb/LVDbSys1-SNAP /mnt/backup_snap_root -t xfs


EXT filesystem:

$mdkir /mnt/backup_snap_root

$mount /dev/VGExaDb/LVDbSys1-SNAP /mnt/backup_snap_root


Step 6 : Take backup of files with tar command.

Here you can play around with different tar attributes.

$tar -cpzvf /export/backup_lvm01/OS_BACKUP/`hostname`/LVDbSys1/`hostname`_LVDbSys1}_`date +%F`.tar.gz -C /mnt/backup_snap_root . --acls


Repeat the same steps for the following mount points:

  • /u01
  • /home
  • /tmp
  • /var
  • /var/log
  • /var/log/audit

You can use “lvs” command to identify the logical volume name for each mount point:


In the above picture, if you noticed there are 2 logical volumes for var mount point. For backup of /var mount point, you need to select correct logical volume depending upon root logical volume group i.e. if the active partition is LVDbSys1 then select LVDbVar1 and if LVDbSys2 is active then select LVDbVar2 for backup of /var mount point.


After backup complete, it is important to remove snapshot logical volume:

$umount /mnt/backup_snap_root

$/sbin/lvremove -f /dev/VGExaDb/LVDbSys1-SNAP

 

This document is only for learning purpose and always validate in the LAB environment first before applying in the LIVE environment.


Hope so you like this article
!
Please share your valuable feedback/comments/subscribe and follow us below and don’t forget to click on the bell icon to get the latest update. Click here to know more about our pursuit.

Related Articles


Loading

How useful was this post?

Click on a star to rate it!

Average rating / 5. Vote count:

No votes so far! Be the first to rate this post.

As you found this post useful...

Follow us on social media!

We are sorry that this post was not useful for you!

Let us improve this post!

Tell us how we can improve this post?

DBsGuru

Hello and welcome to DBsGuru,DBsGuru is a group of experienced DBA professionals and serves databases and their related community by providing technical blogs, projects, training. Technical blogs are the source of vast information not about databases but its related product like middleware, PL/SQL, replication methodology, and so on.Thanks for the visits!Share Learn Grow!

2 thoughts on “Exadata : Snapshot Filesystem Backup

  1. Thanks a lot.. This is very very useful for beginners to understand both the backup process as Linux Os newbies.

Comments are closed.